Category Archives: Boiler effficiency

Short Cycling Boilers

Boiler Short Cycling is when the boiler overheats and shuts off before reaching peak efficiency. If your boiler just recently started short cycling, there can be many different factors causing this issue.

Thermostat

If your thermostat is out of calibration your burner will be bouncing on and off. If your thermostat has a mercury switch first make sure the thermostat hangs level on the wall. Also look to see if the thermostat is in a cold draft area or possibly hanging on a poorly insulated wall. These could all be contributing factors to your thermostat getting incorrect readings. Then causing your boiler to fire inconsistently.

Air Vents

Air vents are crucial to your system running correctly. If your vents are clogged air will become trapped in your system and it will pressurize causing an air bubble which water wont pass through. Your boiler wont be cycling the water at this point and will overheat quickly causing it to shutoff before being able to distribute hot water throughout the house. Often this will be caught in a boiler maintenance and fixed before causing any issues.

Over sized Boilers

If your boiler is over sized it will satisfy the space heating demands too quickly , then shut down until heat is required again. This is bad because the longer your boiler runs the more efficient it will be. This can often happen when you have multiple zones in a home but only one of them is calling for heat. Therefore the amount of water flowing through the boiler is a fraction of what was expected. When you have an on-off boiler (no modulation) this becomes more prevalent and the more the boiler is over-sized, the more often it will occur. A modulating boiler does good in this circumstance because it will adjust the flame according to the load, rather then just shutting down on high limit from lack of flow.

Circulating Pumps

Circulating pumps are used to force hot water from the boiler through the radiating devices such as hot water baseboards or radiators. The circulators are switched on as needed or in some cases they will be designed to run continuously. If your pump stops working it will no longer be able to circulate the water in the zone causing your boiler to overheat and begin short cycling.

Boiler Dry Cycling

When the boiler currently at the temperature set point and is in stand by mode as no further heat is required from the system load (no zones calling for heat). Due to the ambient radiated heat loses, together with the flue drought heat losses (standing losses) The boiler will naturally cool down over time which may cause the temperature controls to instruct the boiler to re fire and return the boiler back to the set point temperature. In this case the heat is not being used by the heating system it is only replacing the “standing heat loss” and therefore wasting energy.

Boiler short cycling is unhealthy overall for your system. If you have any boiler issues in Northern Colorado, call Ace Hi Plumbing, Heating and Air Conditioning, Today and schedule an appointment with one of our heating specialists.

 

The Advantages of Installing a Boiler for Your Heating

Boilers were among the first of whole home heating systems, so they’ve been around a long time – but don’t let that imply they are not up to date with today’s standard for energy efficiency. Today’s boilers have average efficiency ratings of 89%, in addition to providing other benefits for your home heating. But quality installation is just as important as having good equipment, so if you are ready to install a boiler in Northern Colorado, make sure you call the people you can trust: Ace Hi Plumbing, Heating and Air.

Two Types of Boilers

Boilers are part of a hydronic system, meaning they use hot water or steam to heat your home. There are two ways in which the water can be heated

  • Water Tube
  • Fire Tube

With a water tube boiler, the water is held inside metal tubes that are heated on the outside via flames or hot gases. In a fire tube boiler, the opposite occurs : tubes are placed inside the water container; the tubes are then heated with combustion gases. and the heat from the tubes transfers into the water. The two most common fuels used are gas and oil, but other fuels like wood or wood pellets can also be used.

Advantages of Boiler Systems Comparative to Furnaces

Boiler systems have a few advantages that make them attractive to homeowners:

  • Good for allergy sufferers – hydronic systems do not rely on forced air distribution, instead utilizing radiant heating systems or radiators. As such, there is no circulating dust to worry about, which can be very beneficial should you have allergy sufferers in your home.
  • Even gradual heating – the heating of a boiler system is very gradual, as outlet points radiate the heat as opposed to blowing it out, as with a forced-air system.
  • Easy zoning – the piping used with a boiler system can be easily zoned then duct-work. Also allows for more comfort from room to room with designated zones.
  • Quiet operation – the only time you hear noise is when your boiler is heating the water in your system, otherwise, the operation is very quiet.
  • Retains heat longer for better over all efficiency. With a furnace, if you open your door you lose a lot of your heat and have to recover that gradually. With a boiler your heat stays retained within the pipes keeping your floors warmer with significantly less heat loss.

Hydronic heating is a safe, comfortable and economical way to heat your home. Hydronic systems circulate hot water through baseboards, radiators and or radiant tubing in your floors or ceilings. There are many advantages to heating your home using a hydronic system, whether it is a new install or retrofit for your existing system.

The Importance of Boiler Maintenance

One of the most significant reasons why good boiler maintenance is so important is because it helps prevent unexpected shutdowns which could not only be inconvenient but also costly for after hours calls. Getting set up on a scheduled boiler maintenance and inspection helps increase the life of your boiler and takes all the worry out of the last minute service calls.

This scheduled maintenance is especially important to check for leaks on your flues and heat exchanger. If your flue or heat exchanger is damaged from lack of maintenance you are putting you and your family at risk of Co2 exposure. Your boiler technician will check for Co2 levels to make sure your family is safe against this silent killer. This also goes for a heat exchanger on your furnace.

Side Arm Tanks

Side arms tanks are used so that the boiler can provide both space heating and domestic hot water (DHW). The tank stores a consistent temperature water similar to a hot water tank so when there is a call for heat in the home your hot water use will not be compromised. These can really make a huge difference in your home comfort if you already have a boiler without a sidearm that also provides DHW for your home. The thermal mass of the side arm tank stabilizes domestic hot water delivery temperature during long demand periods. This help reduce fluctuation in delivery temperature throughout your daily use.

 

 

Boilers have been around a long time for good reasons. If you think a boiler system in Loveland is a good fit for you, call Ace Hi Heating and Air Conditioning, Today and schedule an appointment with one of our installation specialists.